SYSTEM WARNING: 'date_default_timezone_get(): It is not safe to rely on the system's timezone settings. You are *required* to use the date.timezone setting or the date_default_timezone_set() function. In case you used any of those methods and you are still getting this warning, you most likely misspelled the timezone identifier. We selected the timezone 'UTC' for now, but please set date.timezone to select your timezone.' in '/usr/share/mantis/www/core.php' line 264

0001408: Add Real Time Streaming Protocol (RTSP) NAT support - MantisBT
MantisBT - Endian Firewall
View Issue Details
0001408Endian FirewallFirewall (iptables)public2008-10-28 10:202009-06-10 12:55
nonux21 
 
normalfeatureN/A
newopen 
2.2-rc3 
 
0001408: Add Real Time Streaming Protocol (RTSP) NAT support
Would be nice if the Endian Firewall Community edition could support RTSP NAT.

In fact, I'm trying to move from IPCOP to Endian Firewall.

The current IPCOP setup permits to load 2 modules I used daily to NAT my TV (through my ISP):
ip_conntrack_rtsp
ip_nat_rtsp

I'm not quite sure these modules (or similar) are available in the default
setup of EFW community edition 2.2 RC3.

I assume I'm not the only one using this kind of service (I hope so at
least :) ) but I didn't found any valuable information on the different
help/mailing list on this topic.

Thanks for the advice.

Regards.
No tags attached.
Issue History
2008-10-28 10:20nonux21New Issue
2008-10-28 10:20nonux21Assigned To => peter-endian
2008-12-04 08:55chanhhtNote Added: 0001840
2008-12-04 11:38chanhhtNote Added: 0001841
2008-12-04 19:56nonux21Note Added: 0001842
2008-12-05 01:55chanhhtNote Added: 0001843
2008-12-05 10:07chanhhtNote Added: 0001844
2008-12-24 08:40chanhhtNote Added: 0001910
2009-06-10 12:55peter-endianAssigned Topeter-endian =>

Notes
(0001840)
chanhht   
2008-12-04 08:55   
Hi all,
EFW community edition 2.2 RC3.
Real Time Streaming Protocol (RTSP) NAT support ?? Are you sure ?
Could you help me !
I'm just install EFW community edition 2.2 RC3 ,but Protocol (RTSP)NAT not run
I’m looking forward to your reply.
(0001841)
chanhht   
2008-12-04 11:38   
hi nonux21,
Do you have 2 modules
ip_conntrack_rtsp
ip_nat_rtsp
Could you send to me, because My projec must have NAT RTSP if don't have this then My projec will be die , this projec very important with me !!
I’m looking forward to your reply.
(0001842)
nonux21   
2008-12-04 19:56   
Unfortunately not, that's why I've opened this feature request. It seems we're at least 2 people requesting the same feature. That's a good starting point for the consideration by the dev team :)
(0001843)
chanhht   
2008-12-05 01:55   
Hi nonux21,
I'm only focus IPCop, not EFW community edition 2.2 RC3.
In your top topic ,
You say:
"The current IPCOP setup permits to load 2 modules I used daily to NAT my TV (through my ISP):
ip_conntrack_rtsp
ip_nat_rtsp "
Could you send me 2 module please !!
I’m looking forward to your reply.
Thanks many!
(0001844)
chanhht   
2008-12-05 10:07   
Hi nonux21,
I'm just Install success two module ip_conntrack_rtsp &
ip_nat_rtsp. Now receive traffic Real Time Streaming, But I'm just test some minutes then it have some problem when start a lots of session! IPCop can't load traffic and crash ! coud you have any idea about it!
(0001910)
chanhht   
2008-12-24 08:40   
Hi all,
Endian Firewall Community edition could support RTSP NAT ?
Does the development team has completed construction of this feature has not, can tell us